Download Article

Download Article

If you have a cracked mirror, don't throw it abroad but yet! You can easily repair information technology using a standard windshield repair kit from your local automobile supply shop. Start by cleaning off the mirror to remove any grit and residue. So, employ the stabilizer strip and so yous can inject the resin adhesive and comprise it. Subsequently it dries, add together some other drop resin, comprehend it with a curing motion picture, and give information technology an hour to cure. Peel off the curing film, scrape off the excess resin, and polish the mirror with glass cleaner. It'll await good as new!

  1. 1

    Clean the mirror with soap and warm water. Take a sponge or a clean cloth and soak it in warm water. Apply a drop of dish soap and work the sponge or textile into a soap. Wipe the cracked expanse clean to remove dirt and dust from the surface.[1]

    • Dirt, dust, and debris can affect how well the resin fills the crevice, so be sure to clean the expanse well!
    • Remove any loose fragments of glass from the scissure.

  2. 2

    Remove the adhesive backing of the stabilizer moving-picture show. Accept the clear stabilizer strip and locate the edge of the adhesive backing. Utilise your fingertips to peel off the backing to expose the adhesive.[2]

    • Don't peel off the adhesive backing until y'all're ready to apply the motion picture.
    • Be conscientious not to allow the motion picture to stick to itself or information technology may no longer exist effective.

    Advertisement

  3. 3

    Press the stabilizer film over the cleft. Place a corner of the stabilizer motion-picture show onto the mirror at the border of the crack. Apply the movie over the crack by rolling it over the surface from the corner so no air gets trapped beneath the picture.[iii]

    • Avoid removing the film and reapplying it or information technology could affect how well it adheres and go out behind a gluey rest.

    Tip: If you can't encompass the crack using 1 stabilizer film, use more! Arrange the films then their edges are flush against each other and they embrace the unabridged crevice in the mirror.

  4. 4

    Use your fingers to polish out the stabilizer picture show. Run your fingertips from one end of the stabilizer motion-picture show to the other. Work to push out whatsoever air bubbling that may exist trapped beneath the film and create a tight seal over the crack.[four]

    • Brand sure there aren't any creases or bubbles in the movie.

    Advertisement

  1. 1

    Fill the syringe with the epoxy resin adhesive. The epoxy resin adhesive comes with a plastic syringe. Push the plunger of the syringe so it's all the way down, then insert the syringe into the container of resin. Slowly pull the plunger to pull out the resin and make full the syringe.

    • Yous may need to cut the tip of the syringe with a pair of pair of scissors in order to use it.
    • If the resin did not come with a syringe, you can find one at an motorcar supply store, department store, or online.

    Tip: If yous have a glass repair kit that has resin in a container with an applicator tip, utilize that instead of a syringe.

  2. 2

    Insert the tip of the syringe through the stabilizer motion-picture show. Place the tip of the syringe over the stabilizer film roughly at the center. Use gentle pressure to push the syringe through the moving-picture show and into the crack.

    • The tip of the syringe should exist inside of the crack.

  3. iii

    Push downward the plunger to fill the crack with resin. Go on the syringe even so and slowly push on the plunger. The resin will leave the syringe and make full the crack. The stabilizer motion-picture show will keep the resin contained in the scissure.

    • Add a modest corporeality of resin at a fourth dimension. If yous utilize likewise much as well quickly it could form an uneven bulge under the film.

  4. 4

    Await 20 minutes to allow the resin to harden. Later on you utilise the resin to the crack, slowly pull the tip of the syringe out of the stabilizer motion-picture show. Go out the resin undisturbed for at least 10 minutes then it tin can kickoff to set and harden in the crack.[5]

    • Check the packaging of the resin agglutinative for specific drying times.
    • Ready an warning on your telephone or clock for xx minutes.

    Ad

  1. 1

    Skin off the stabilizer film. Use your fingernails to pry upwards a corner of the stabilizer film. Use 1 polish movement to gently remove the film by peeling it off.[vi]

    • Don't apply quick or hasty movements or you could tear off a section of the film.
    • Use a razor blade to get underneath the picture if you can't peel it off with your fingertips.

  2. 2

    Add together a drop of the resin over the crack and cover it with the curing moving-picture show. Use the syringe to squeeze out a small drop of the resin adhesive over the freshly filled crack. Take the curing film and press information technology over the crack. The small drop of resin will spread out nether the moving picture to cover the scissure.[7]

    • Use your fingers or a razor blade to smooth out the curing film and remove any bubbles from below it.

    Tip: If you need to apply more than than 1 curing film to embrace the crack, add together a drop of resin for each film that you demand to place. Make sure you comprehend the entire crack!

  3. 3

    Await one hr to allow the resin to cure. Get out the curing film completely undisturbed to allow the resin to fully gear up and cure in the scissure.[8]

    • Check the packaging of the resin for the specific curing time.
    • Aim a fan at the mirror to assistance information technology cure faster.
    • Set an warning for an hour so you tin can exist sure when the resin is washed curing.

  4. 4

    Remove the curing film and scrape away the backlog resin. Pry up a corner of the curing film with your fingertips and gently peel it off. Try to use 1 smooth, fluid motion so the strip comes off cleanly. Take a razor blade or a utility knife and gently scrape over the top of the crack to remove any excess resin.[ix]

    • Be conscientious not to scratch the resin of the glass of the mirror.
    • Angle the razor blade or utility pocketknife so information technology'southward parallel with the surface to run information technology over the crack evenly.

  5. 5

    Clean the area with glass cleaner. Shine the repaired mirror by spraying some drinking glass cleaner over the entire surface. Use a make clean cloth and rub the mirror in round motions to vitrify information technology clean.[10]

    • Don't saturate the mirror with glass cleaner.
    • Yous can discover glass cleaner at department stores and online.

    Advertisement

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Thanks for submitting a tip for review!

Things You'll Need

  • Drinking glass repair kit with stabilizer moving picture, resin adhesive, syringe, and curing pic
  • Razor blade or utility knife
  • Glass cleaner

References

About This Article

Thanks to all authors for creating a folio that has been read 97,610 times.

Did this article help y'all?